H2SV-10-C siemens flender gear units Helical gearboxes H2

Flender/Flender Gear Units/Helical gearboxes H2

0 XSS7-1H-BK 7 J0 XSS7-1H-BK Double reduction stainless gearboxes require the primary and secondary boxes to be filled independently to their respective mounting position .Oil Capacity in Fluid Ounces (SS7 Units Only) Unit SizePositions 1 2 3 4 5 & 6 7 3 .2 3 .2 4 .8 3 .2 3 .2 7 1 .2 1 .6 1 .6 1 .6 1 .6 7 1 .4 1 .6 2 .8 1 .6 1 .6 7 1 .6 2 .8 2 .4 2 .8 2 .8 7 2 .0 2 .5 2 .5 2 .5 2 .5 7 3 .0 3 .0 4 .5 3 .0 3 .0 7 8 .5 8 .0 9 .0 8 .0 8 .0Replacement Hardware Covers Housing Bearing Mounting Output Motor Flange Size Oil Plugs Carrier Feet Flange B5/B7 B9 (5C/1TC) (1TC) 7 J0 / / J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 7 J0 J0 J0 J0 J0 J0 & J0 J0 has nominal . of 0 .6" J0 has nominal . . of 0 .8" Material: Stainless Steel disk (metal detectable) with over-molded rubber Table 1: Hollow Output Shaft Bore Codes Fraction Output Decimal Key Size Bore Code7 7 7 7 7 7 7 Size* Size 5/8 P1 .6 .1 .1 1 .0 3/4 P1 .7 .1 .1 1 .0 7/8 P1 .8 .1 .1 1 .0 1/1 P1 .9 .2 .2 1 .3 1 P1 1 .0 .2 .2 1 .3 1-1/8 P1 1 .1 .2 .2 1 .3 1-3/1 P1 1 .1 .2 .2 1 .3 1-1/4 P2 1 .2 .2 .2 1 .3 1-7/1 P2 1 .4 .3 .3 1 .7 1-1/2 P2 1 .5 .3 .3 1 .7 1-1/1 P3 1 .9 .5 .3 2 .0 2 P3 2 .0 .5 .3 2 .0 2 3/1 P3 2 .1 .5 .3 2 .0 *Bore tolerance + .0 / .0 Standard Bore Included in Express Program Optional Bore Rectangular key is provided with reducer to fit hollow shaft . Drive shaft requires standard width and depth keyway . Note: For all other bore sizes, contact factory . NOTE: ouble input seals are required for all positions except #1 and #5.Ambient (Room) Temp .Recommended Oil (or equivalent)Viscosity Range SUS FLENDER GRAFFENSTADEN 1FISO Viscosity Grade No .Klubersynth UH1 6-4 Qt . Part No . -2 to 2F** (-2 to 1C)Klubersynth* UH1 6-4 Synthetic H1 Food Grade Oil1/2 4 6 * Synthetic recommendation is exclusiv