B2-CH-14-D for horizontal gear units o n r e q u e s tGear u Bevel-helical gear reducer B2
In stock
SKU
B2-CH-14-D
$11,571.43
Flender/Flender Gear Units/Bevel-helical gear reducer B2
MEC//0/2/0 REVISION : 0 SHOP & FIELD PAINTING EDITION : 1 PAINT SYSTEM . NO. DESIGN TEMPERATUR IN SURFACE PREPARATIO
FIELD PRIMER FINISH PAINT TOTAL DFT IN MICRONS (MIN.) REMARKS 8.4 8 TO 2 SSPC-SP-1 REPAIR OF PRE-FABRICATION PRIMER 1 
COAT OF -9 FLENDER GRAFFENSTADEN 6-7 DFT/ COAT 3 COATS OF -1 FLENDER GRAFFENSTADEN 2 DFT/ COAT 3 2 = 
6 1 8.5 2 TO 4 SSPC-SP-1 REPAIR OF PRE-FABRICATION PRIMER 1 COAT OF -9 FLENDER GRAFFENSTADEN 6-7 DFT/ COAT 
2 COATS OF -1 FLENDER GRAFFENSTADEN 2 DFT/ COAT 2 2 = 4 1 8.6 4 TO 5 SSPC-SP-1 REPAIR AS PER 7.2.2 2 COATS OF -1 FLENDER GRAFFENSTADEN 2 DFT/ COAT 2 2 = 4 8 NOTE 1 : FOR MS CHIMNEY OR WITHOUT REFRACTORY LINING 8.3, 8.4 AND 8.5 SHALL BE FOLOWED. NOTE 2 : FOR EXTENAL SURFACE OF RCC CHMNEY: 2 COATS OF -6 FLENDER GRAFFENSTADEN 1 DFT/ COAT TO OBBTAIN 2 1=2 SHALL BE APPLIED AFTER MAKING SURFACE PREPARATION AS PER GUIDELINES IN 1.5 NOTE 3 : WHEREVER REQUIRED .NO. 8.3 SHALL BE USED FOR 1C TO 8C AND .NO. 8.2 WILL BE DELETED. 9 of 1 STANDARD TECHNICAL SPECIFICATION MECON LIMITED REGD. OFF: RANCHI 8 OIL & GAS SBU, DELHI DOCUMENT NO. Page 2 of 5 TITLE MEC//0/2/0 REVISION : 0 SHOP & FIELD PAINTING EDITION : 1 TABLE 9.0: FIELD PAINT SYSTEM FOR CORROSIVE ENVI RONMENT (FOR CARBON STEEL, LOW TEMPERATURE CARBON STEEL & LOW ALLOY STEEL) FOR ALL CORROSIVE AREAS ABOVE GROUND WHERE 2S, SO 2 FUMES OR SPILLAGES OF ACID/ ALKALI/ SALT ARE LIKELY TO COME IN CONTACT WITH SURFACE SUCH AS EXTERNAL SURFACE OF UNINSULATED COLUMNS, VESSELS, HEAT EXCHANGERS, BLOWERS, PIPING, PUMPS, TOWERS, COMPRESSORS, FLARE LINES, STRUCTURAL STEEL ETC. PAINT SYSTEM . NO. DESIGN TEMPERATUR IN SURFACE PREPARATION FIELD PRIMER FINISH PAINT TOTAL DFT IN MICRONS (MIN.) REMARKS 9.1 -9 TO 1 SSPC-SP-1 REPAIR OF PRE-FABRICATION PRIMER 1 COAT OF -9 FLENDER GRAFFENSTADEN 6-7 DFT/ COAT NONE 6-7 Repair of pre-erection/ pre fabrication primer shall be done wherever damage is observed. 9.2 -1 TO 8 SSPC-SP-1 REPAIR OF PRE-FABRICATION PRIMER 1 COAT OF -9 FLENDER GRAFFENSTADEN 6-7 DFT/ COAT + 1 COATS OF -6 FLENDER GRAFFENSTADEN 4 DFT/ COAT 1 COATS OF -6 FLENDER GRAFFENSTADEN 1 DFT/ COAT| Model Type | Bevel-helical gear reducer B2 |
|---|---|
| Gear Type | Bevel Helical Gear |
| Weight (kg) | 540.000000 |
| Ratio Range | 1 : 6.3…22.4 |
| Low Speed Output | Solid shaft without parallel key |
| Nominal Torque | 101000 Nm |
| Mounting Arrangements | Horizontal mounting position |
| Manufacturer | Flender..Ltd China(Tianjin) |
| Country of Manufacture | China |
| Data Sheet & Drawings | B2-CH-14-D for horizontal gear units o n r e q u e s tGear u Bevel-helical gear reducer B2 |
Related Products
